Skip to content

How to Configure Zabbix Agent

Last Updated on September 18, 2022 by Climent Rick

Zabbix Agent is a software that allows you to monitor your server. It can be installed on any operating system, and it is available for free. In this guide, we will show you how to install and configure Zabbix Agent on CentOS 7.

  • Download the Zabbix Agent from the official website
  • Extract the files to a desired location on your server
  • Open the “zabbix_agentd
  • conf” file in a text editor and configure the parameters according to your environment
  • Save and close the file
  • Start the Zabbix Agent service/daemon and enable it to start automatically on boot up

How to Configure Zabbix Agent on Windows

If you’re looking to get started with monitoring on Windows with Zabbix, one of the first things you’ll need to do is install and configure the Zabbix agent. In this blog post, we’ll walk you through everything you need to know about installing and configuring a Zabbix agent on Windows. First, download the latest version of the Zabbix agent from the official website.

Once you have the installer file, launch it and follow the prompts. During installation, you’ll be asked to select which components you want to install – make sure to select both “Zabbix Agent” and “Zabbix Trapper”. Next, open up your Zabbix server web interface in your browser and go to “Configuration” -> “Hosts”.

Click on the “Create Host” button and fill in all of the required information. Be sure to set the “Host name” field to match exactly what you entered during installation of the agent (including case). On this same page, scroll down until you see the section for “Agent interfaces”.

Here, create a new interface and set the following parameters: * Type: SNMPv2 * Connection type: UDP/IPv4 * Port number: 10050 * IP address: Leave blank (will be auto-populated) Now that your host is configured, we can move on to setting up some items.

Items are what actually monitor specific metrics on your server – for example, CPU usage or free disk space. Go back to the main screen of your Zabbix server web interface and click on “Configuration” -> “Items”. Then click on the “Create Item” button.

On this page, fill in all of the required fields – most importantly, be sure that under both “Key” and “$1”, enter zabbix_agentd[“cpu”,”total”] . This key will return total CPU usage across all cores as a percentage value; other available keys can be found in Zabbix’s documentation . After filling out all required fields here , scroll down and click on Add .

Your item should now appear in list under Configuration -> Items . If it does not , check previous steps for any errors . Now let’s create a trigger for this item so we can receive an alert if our CPU usage exceeds 80%.

Zabbix Agent Config File

Zabbix Agent Config File The Zabbix agent configuration file is located in the conf directory. The file is named zabbix_agentd.conf and contains parameters that control the operation of the agent.

The main parameter that must be configured is Server, which specifies the IP address or hostname of the Zabbix server. The AgentPort parameter can also be specified to use a port other than the default 10050. If encryption is enabled on the server, then the StartTLS flag must also be set to true.

Other parameters that can be configured include DebugLevel, LogFile, and PidFile. These parameters are typically not required to be changed. Once all required parameters have been set, save the file and restart the Zabbix agent service for changes to take effect.

Configure Zabbix Agent Linux

Zabbix is a powerful monitoring tool that can be used to monitor various aspects of a Linux system. In this tutorial, we will show you how to install and configure Zabbix Agent on a Linux system. We will start by installing the Zabbix Agent on our Linux system.

You can download the latest version of the Zabbix Agent from the official website. Once you have downloaded the agent, you can install it using the following command: tar -xvzf zabbix-2.4.7.tar.gz

cd zabbix-2.4.7 ./configure –enable-agent make install

Now that the Zabbix Agent is installed, we need to configure it so that it can communicate with our Zabbix Server. We will edit the file /etc/zabbix/zabbix_agentd.conf and make sure that the following lines are uncommented and set to the correct values: Hostname=MyLinuxServer #Set this to the hostname of your server

Zabbix Agent Configuration Example

If you’re looking to get started with monitoring your servers and infrastructure with Zabbix, one of the first things you’ll need to do is configure the Zabbix agent on each system. In this blog post, we’ll take a look at a Zabbix agent configuration example that will show you the basics of what you need to do. The first thing you’ll need to do is edit the zabbix_agentd.conf file and uncomment the following lines:

### Option: ListenIP # IP address that Zabbix agent should listen on. Cannot be specified together with ‘ListenPort’.

# If IPv6 support is enabled then ‘ListenIP’ can accept an IPv6 address too. # Default: disabled ### Option: ListenPort

# Port that Zabbix agent should listen on. Cannot be specified together with ‘ListenIP’. # Default: 10050

Next, specify which server(s) or proxy(ies) the agent should connect to using one or both of these directives: ### Option: ServerActive or ProxyMode (since 2.0) //proxy mode – added in 2.0 version; used if ProxyServer directive is not defined in config file; only single proxy allowed per host; multiple proxies must use different ports for communication //server active – older directive; several active servers may be configured for failover purposes; multiple proxies are supported After that, decide how often (in seconds) data should be collected by setting this directive:    

### Option : Interval   //this parameter defines interval between checks performed by Agent – so it’s time between sending information from monitored device/service to Zabbix Server/Proxy – check man zabbix_agentd for more details about other parameters available in config file (BufferSend , BufferSize etc.) By default value equals 60 seconds but depending on needs it can be set as low as 1 second or even less                                                               # Check every 10 seconds for new values                  Interval=10s

That’s really all there is to basic agent configuration!

Zabbix Agent Config File Location Linux

If you’re looking for information on where the Zabbix Agent config file is located on a Linux system, you’ve come to the right place. In this blog post, we’ll discuss the location of the config file and how to change it if necessary. The Zabbix Agent config file is typically located in one of two places: either /etc/zabbix/ or /usr/local/etc/.

If you’re not sure which directory your config file is in, you can check by running the following command: find / -name zabbix_agentd.conf Once you know where your config file is located, you can open it in a text editor and make any necessary changes.

Be sure to save your changes before exiting the editor. That’s all there is to changing the Zabbix Agent config file!

How to Configure Zabbix Agent
How to Configure Zabbix Agent 2


How Do I Install And Configure Zabbix Agent in Windows?

Zabbix is an enterprise open source monitoring solution for networks and applications, created by Alexei Vladishev. It is designed to monitor and track the status of various network services, servers, and other networking equipment. The Zabbix agent is a small piece of software that needs to be installed on any machine that you want to monitor.

The agent will collect data from the system it’s running on and send it back to the Zabbix server for further processing. In this article we’ll show you how to install and configure the Zabbix agent on a Windows machine. Before we start, please note that in order for the agent to work properly, you need to allow incoming traffic on port 10050/tcp in your firewall settings.

Installing the Agent # There are two ways you can install the Zabbix agent – using a pre-compiled binary or compiling it yourself from source code. If you choose to use a pre-compiled binary, you can download it from the official Zabbix website (

How Do I Start a Zabbix Agent in Linux?

If you want to monitor a Linux server with Zabbix, you’ll need to install and configure the Zabbix agent on that machine. In this article, we’ll show you how to do that on a CentOS 7 server. First, we’ll need to download the Zabbix agent RPM package from the Zabbix website.

You can find the latest version of the agent here:

Once you have the RPM file, you can install it with the following command: sudo yum install zabbix-agent-3.4.*.rpm

Next, we’ll need to edit the Zabbix agent configuration file located at /etc/zabbix/zabbix_agentd.conf . We’ll need to set up a few parameters in this file before starting the agent. First, find the line that says # ListenIP and change it to look like this:

ListenIP=192.168.*.* Replace 192.168.*.

* with your server’s IP address or hostname (if your server has a DNS record). Next, find the line that says # Server and change it so that it points to your Zabbix server’s IP address or hostname: Server=192.168.*.*

Again, make sure to replace 192.168.*.* with your actual Zabxib server IP address or hostname . Finally, we needto tellthe agen which porttousefor communicationby findingthe line thatsays Portandchangingitfrom 10050to whateverportyou configuredyourZabxibservertouse(usually10051) :Port = 10051 Saveandexit th efilewhenyou’redonewiththosechanges .

Where Zabbix Agent Config File in Linux?

Zabbix agent config file is located in /etc/zabbix/zabbix_agentd.conf. In the Zabbix agent configuration file, you can configure various parameters that define how the Zabbix agent will work. These parameters include AgentName, Server, ListenPort, DebugLevel, LogFile, PidFile, etc.

How Do I Check Zabbix Agent Status in Linux?

To check the status of a Zabbix agent on a Linux machine, you can use either the command line or the web-based interface. If you want to use the command line, you will need to connect to the server via SSH and run the following command: ps -aux | grep zabbix_agentd

This will list all of the processes that are currently running on the server, and you will be able to see if the Zabbix agent is running or not. If it is running, you should see something like this: /usr/sbin/zabbix_agentd -c /etc/zabbix/zabbix_agentd.conf -p /var/run/zabbix/

0 S root 2427 748 0 80 0 – 2 May02 ? 00:00:00 [kworker/0:1] 1 S root 1 0 0 1006 568 pts/$USER Sl+ 4:21 0:00 grep –color=auto zabbix_agentd

If it is not running, you will only see the grep process listed. To start the Zabbix agent, simply run this command:


If you’re looking to get started with monitoring using Zabbix, one of the first things you’ll need to do is configure a Zabbix agent. In this post, we’ll go over how to install and configure a Zabbix agent on Ubuntu 18.04. We’ll also cover how to set up some basic monitoring items so that you can start collecting data from your server.

Leave a Reply

Your email address will not be published.